Skip to main content

Mk. 1 - 4 Prototype Frame for a Shelter with Green House Walls for Containing Veg or Plants or Garden Office / Shed with Shelves

Mk. 1 & 2 Prototype Frame for a Shelter with Green House Walls for Containing Veg or Plants


2m long  frame made of composite door off cuts with shelves joining tehn for plants or veg to sit on. Complete boxes may be installed, using an off cut at front of shelf . the rear with have a complete sheet, though windows may be added.


Close up of joint

A joining shelf is added, which will connect it to another upright

Close up of corner


Mk 2. Beam upright (no shelves as yet),
Close up of end. It show 2  side grp edge strip. Edge strips have been added to contain the window off cuts im middel & take extra weight. All are glued as well as screwed



Close up
Full length view
End view
Frame will be covered on outside with grp sheet that lets 90% of light through, but keeps bugs / wind out
Close up


 M3. with 1 Mk 4. "curved" upright on the right end .

a covering strip will be screwed to edge of shelf both sides to hide & waterproof nails head
 Close up of mk 4 upright
 Close up of mk 3 upright (2 versions with side beams further in / out)
 Other side of mk 3 upright
 With clear grp sheets (fixings to bge decided as grp sheets may be removable to access palnts if inside has insulated panel. Perhaps using butterfly nuts)
Close up showing plant hardly visible
 Extreme close up
 Other side of Mk 4 curved upright

Comments

Popular posts from this blog

Paul Ridley, Founder of the Cabinz Project has invented "Shelter Banks" Where People Can Collect Materials to Build Basic Shelters

Press Release:

"Shelter Banks" Similar to Food Banks.Providing Building Materials For Outbuildings, to People Squeezed Into The Smallest Houses in Europe


The Uk Property market has been in crisis for many years. The new concept of Shelter Banks, aims to help ease a part of that crisis.

They are similar to Food Banks in the Uk, but distributing, re-used & re-manufactured building materials that have been donated or bought in bulk at low cost.
The shelters built with these materials, may be storage sheds, greenhouse or insulated garden offices for small businesses.

To facilitate this, building materials are stored in a warehouse and collected by local people, or posted to target low income groups, individuals or small businesses over a wider area.

Some materials will be free, but it depends on the amount of resources, funding & donations available, as to whether materials will have to have a small charge. If so, due to low overheads & donator support, they will much chea…

Treated 6mm Birch Plywood Shingle Off Cut Cladding Shelter Experiment

Treated 6mm Birch Plywood Shingle was screwed to 2m Plastic Door edge strip (DES) horizontal battons. 42mm & 75mm drywall screws were used (no extra glue)

The off cuts were donated from a local fencing co. that also make rabbit hutches, from which these off cuts arose

Off cuts were dipped in decking / fencing preserver, so a few 'tide marks' are present.
This was done to get more preserver deeper into the wood .

We wait to see how it weathers & it will hopefully make our first prototype shelter more attractive (still going strong after 2.3 yrs)

More off cut cladding picture variations to come 

Some off cuts have been donated to Woodcraft to Wellness Chester













Close up







Hurricane Damaged Shelter Recovery Method for British Virgin /Caribbean Islands / Usa with little or no budget

Hurricane Damaged Shelter Recovery Proposal Method for British Virgin /Caribbean Islands / Usa with little or no budget
Hurricanes Harvey and Irma Damage, America Can’t Afford to Rebuild 
Method 
1. Collect wood that is plentiful due to fallen trees / joists / stick frames 
2. Sort or cut wood into 50mm /70 / 140mm thick planks
3. paints planks with preservative 
4. Clad & nail / screw planks inside galvanised drywall lining channel or purlins, salvaged from destroyed buildings 
5.Drill holes in structurally sound brick walls, insert plastic walls plugs , glued in with injection resin or adhesives
6. Screw metal clad  planks to wall, horizontally & vertically , so a 2.4 x1.2m sheet can be screwed to it    
7  Fill insulation voids with plastic bottles filled with polystyrene or bubble wrap (or sand / soil / water if thermal mass / heavier wall weight required) .